If you have been reading about System suitability and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Updated 2026-04-10. Numbers and descriptions here follow the published literature rather than marketing material.
Practical HPLC testing depends on careful sample preparation and instrument maintenance. Samples may require filtration, dilution, pH adjustment, or extraction to avoid column damage and matrix interference. Mobile phases are degassed and filtered, and columns are equilibrated before injection. Common problems include peak tailing, baseline drift, ghost peaks, carryover, and co-elution of analytes. Documentation of instrument logs, calibration records, and electronic audit trails supports data integrity and traceability. Ongoing training and routine maintenance help reduce variability between analysts and laboratories.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
Method validation demonstrates that an analytical procedure is suitable for its intended purpose. Typical validation characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulatory guidance from bodies such as the International Council for Harmonisation and the United States Pharmacopeia outlines expectations, though specific criteria depend on the product and method. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, column efficiency, and injection repeatability. Failure of these checks can invalidate a batch of measurements.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
| Parameter | Typical acceptance criterion | Notes |
|---|---|---|
| Resolution | ≥ 1.5 | Baseline separation of adjacent peaks |
| Tailing factor | ≤ 2.0 | Peak symmetry measure |
| Theoretical plates | > 2000 | Column efficiency indicator |
| Injection repeatability | ≤ 2% RSD | Relative standard deviation for replicate injections |
| Linearity | r² ≥ 0.995 | Calibration curve over the working range |
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
Camurus is a company focused on the development of lipid lyotropic liquid crystal structures for pharmaceutical drug delivery applications. These structures are well-defined three-dimensional formations consisting of lipophilic and hydrophilic domains that can be either interconnected or isolated depending on the environmentally induced phase conditions. The unique crystalline structures offer a unique way of encapsulating and transporting Active pharmaceutical ingredients, such as small molecules, peptides and proteins through the body. The structures also allow for the use of controlled release and prevention of degradation of fragile short half live molecules, a serious issue for amino-acid based drugs.
ADP + Pi + 2H+out ⇌ ATP + H2O + 2H+in ATP synthase lies across a cellular membrane and forms an aperture that protons can cross from areas of high concentration to areas of low concentration, imparting energy for the synthesis of ATP. This electrochemical gradient is generated by the electron transport chain and allows cells to store energy in ATP for later use. In prokaryotic cells ATP synthase lies across the plasma membrane, while in eukaryotic cells it lies across the inner mitochondrial membrane. Organisms capable of photosynthesis also have ATP synthase across the thylakoid membrane, which in plants is located in the chloroplast and in cyanobacteria is located in the cytoplasm. ATP synthase is present in all organisms studied. Eukaryotic ATP synthases are F-ATPases (which usually work as ATP synthases instead of ATPases in cellular environments) and running "in reverse" for an ATPase (ATPases catalyze the decomposition of ATP into ADP and a free phosphate ion). This article deals mainly with this type. An F-ATPase consists of two main subunits, FO and F1, which has a rotational motor mechanism allowing for ATP production.
Acta Biochimica et Biophysica Sinica was a Chinese-language journal entitled "Shengwu Huaxue Yu Shengwu Wuli Xuebao" (see box below), which began publishing sometime in 1958 or 1959, or August 1961, until December 2003 (depending on the source). Tables of contents were in English. Summaries (abstracts) were in English and Russian, and text of articles in Chinese. Later issues were promulgated in the Chinese and English languages. The translated title was "Journal of Biochemistry and Biophysics". The frequency was quarterly from 1959 to 1963, bimonthly from 1964 to 2002, and finally, monthly by 2003. Publication was suspended from 1966 to 1975. It was indexed in Chemical Abstracts Service. It may have published 35 volumes in total, over the years. In 2004 the journal switched to a full English-language journal under its current title. Official website Institute of Biochemistry and Cell Biology Archived 2003-12-17 at the Wayback Machine, SIBS, CAS
5-Oxo-ETE and 5-oxo-15(S)-hydroxy-ETE but not 5-hydroxy members of the 5-HETE family such as 5-(S)-HETE activate peroxisome proliferator-activated receptor gamma (PPARγ). This activation does not proceed through OXER1; rather, it involves the direct binding of the oxo analog to PPARγ with 5-oxo-15-(S)-hydroxy-ETE being more potent than 5-oxo-ETE in binding and activating PPARγ. The Activation of OXER1 receptor and PPARγ by the oxo analogs can have opposing effects on cell function. For example, 5-oxo-ETE-bound OXER1 stimulates whereas 5-oxo-ETE-bound PPARγ inhibits the proliferation of various types of human cancer cell lines; this results in 5-oxo-ETE and 5-oxo-15-(S)-HETE having considerably less potency than anticipated in stimulating these cancer cells to proliferate relative to the potency of 5-(S)-HETE, a relationship not closely following the potencies of these three compounds in activating OXER1. 5-Oxo-ETE relaxes pre-contracted human bronchi by a mechanism that does not appear to involve OXER1 but is otherwise undefined.
Sources: en.wikipedia.org
Acceptance sampling uses statistical sampling to determine whether to accept or reject a production lot of material. It has been a common quality control technique used in industry. It is usually done as products leave the factory, or in some cases even within the factory. Most often a producer supplies a consumer with several items and a decision to accept or reject the items is made by determining the number of defective items in a sample from the lot. The lot is accepted if the number of defects falls below where the acceptance number or otherwise the lot is rejected. In general, acceptance sampling is employed when one or several of the following hold: testing is destructive; the cost of 100% inspection is very high; and 100% inspection takes too long. A wide variety of acceptance sampling plans is available. For example, multiple sampling plans use more than two samples to reach a conclusion. A shorter examination period and smaller sample sizes are features of this type of plan. Although the samples are taken at random, the sampling procedure is still reliable.
Albiglutide (trade names Eperzan in Europe and Tanzeum in the US) is a glucagon-like peptide-1 agonist (GLP-1 agonist) drug marketed by GlaxoSmithKline (GSK) for treatment of type 2 diabetes. In 2017 GSK announced Albiglutide's withdrawal from the worldwide market for economic reasons, and remaining stocks in the supply chain were effectively depleted by 2018. Albiglutide was used for the treatment of type 2 diabetes in adults. It can be used alone (if metformin therapy is ineffective or not tolerated) or in combination with other antidiabetic drugs, including insulins. According to a 2015 analysis, albiglutide is less effective than other GLP-1 agonists for lowering glycated hemoglobin (HbA1c, an indicator for long-term blood glucose control) and weight loss. It also seems to have fewer side effects than most other drugs of this class, except for reactions at the injection site which are more common under albiglutide than, for example, under liraglutide.
The manifestation of apical dominance differs significantly between plant groups due to the positioning of their growing points (meristems): Broadleaf plants: The apical meristem is located at the shoot tip, elevated above the ground. Apical dominance is exerted downward, inhibiting axillary buds along the stem. Removing the apex (pruning) releases these buds, resulting in lateral branching and a bushier shape. Grasses: During vegetative growth, the primary apical meristem remains at or near the soil surface in a region called the crown. Growth occurs via intercalary meristems at the base of the leaves. Apical dominance in grasses primarily regulates tillering—the production of new shoots from basal buds. Because the meristem is protected at ground level, grasses can be mown or grazed without destroying the primary growing point, allowing them to recover more quickly than most broadleaf species. Plant physiologists have identified four different stages the plant goes through after the apex is removed (Stages I-IV). The four stages are referred to as:
Animals ingest amino acids in the form of protein. The protein is broken down into its constituent amino acids in the process of digestion. The amino acids are then used to synthesize new proteins and other nitrogenous biomolecules, or they are further catabolized through oxidation to provide a source of energy. The oxidation pathway starts with the removal of the amino group by a transaminase; the amino group is then fed into the urea cycle. The other product of transamidation is a keto acid that enters the citric acid cycle. Glucogenic amino acids can also be converted into glucose, through gluconeogenesis. Of the 20 standard amino acids, nine (His, Ile, Leu, Lys, Met, Phe, Thr, Trp and Val) are called essential amino acids because the human body cannot synthesize them from other compounds at the level needed for normal growth, so they must be obtained from food.
Linear RGD peptides suffer from low binding affinity, rapid degradation by proteases, and lack of specificity for integrin type. RGD can be cyclized, or made into a cyclic compound, via disulfide, thioether, or rigid aromatic ring linkers. This leads to an increase in binding affinity and selectivity for integrin αVβ3 relative to αIIBβ3. For example, the cyclic peptide ACDCRGDCFCG, also known as RGD4C, was shown to be 200-fold more potent than commonly used linear RGD peptides. The structural rigidity of cyclic RGD peptides improves their binding properties and prevents degradation at the highly susceptible aspartic acid residue, thereby increasing their stability. Many RGD derivative drugs and diagnostics are cyclized, including Eptifibatide, Cilengitide, CEND-1, and 18F-Galacto-RGD, and 18F-Fluciclatide-RGD.
Sources: en.wikipedia.org
Biopolymers are polymers produced by living organisms. Cellulose and starch, proteins and peptides, and DNA and RNA are all examples of biopolymers, in which the monomeric units, respectively, are sugars, amino acids, and nucleotides. Cellulose is both the most common biopolymer and the most common organic compound on Earth. About 33% of all plant matter is cellulose. On a similar manner, silk (a proteinaceous biopolymer) has garnered tremendous research interest across various domains, including tissue engineering, regenerative medicine, microfluidics, and drug delivery. Bionics Hydrogel Polymeric surface Surface modification of biomaterials with proteins Synthetic biodegradable polymer List of biomaterials Oxygen generating biomaterial Journal of Biomaterials Applications CREB – Biomedical Engineering Research Centre Archived 2021-05-07 at the Wayback Machine Department of Biomaterials at the Max Planck Institute of Colloids and Interfaces in Potsdam-Golm, Germany Open Innovation Campus for Biomaterials Archived 2009-04-19 at the Wayback Machine
study of complex formation in supramolecular systems – organized ensembles surfactants and macrocyclic ligands; study of coordination compounds of iron (III) and manganese (II) for magnetic resonance imaging; obtaining new types of hybrid organic-inorganic functional materials based on nanoscale hyperbranched structures. Results of these studies are of basic value in the area of coordination chemistry, bioinorganic chemistry, chemistry of nanomaterials, pharmaceutical chemistry. Proposed model and physio-chemical basis of self-assembly of nanoscale of hyperbranched polymers, set new approaches to understanding the mechanisms of gene transfection and targeted drug delivery.
Aerospace 9100 (AS9100) is an international standard for aerospace management systems that is a widely adopted and standardized quality management system for the aerospace sector. It was developed in March 1999 by Society of Automotive Engineers. The goal of the standard is to provide for continual improvement, emphasizing defect prevention and the reduction of variation and waste in the aerospace industry supply chain and assembly process. The standard was designed to fit into an integrated management system. AS9100 replaces the earlier AS9000 and fully incorporates the entirety of the current version of ISO 9001, while adding requirements relating to quality and safety. Major aerospace manufacturers and suppliers worldwide require compliance with AS9100 as a condition of doing business with them.
Bont possesses no superhuman abilities, but he occasionally used Mutant Growth Hormone, a substance that temporarily enhanced his speed and strength and caused his eyes to emit a green glow. Sigourney Weaver portrays a female version of Alexander Bont, primarily known as Alexandra, in The Defenders. This version is the leader of the Hand. Alexandra is described as an "adversary" rather than a villain and was intended to be portrayed sympathically as a supporting character in Elektra Natchios' story. Alexandra is one of the five "fingers" of the Hand, who all gained immortality using the healing powers of qi. Following the death of Elektra, Alexandra resurrects her to create the ancient weapon Black Sky, which is prophesied to destroy all enemies of the Hand. Alexandra intends to use Elektra to steal the Iron Fist from Danny Rand. However, Elektra regains her memories of her previous life and kills Alexandra, claiming leadership of the Hand. http://www.marvunapp.com/Appendix4/bontalexander.htm http://www.imdb.com/title/tt1784594/
Analysis of molecular variance (AMOVA), is a statistical model for the molecular algorithm in a single species, typically biological. The name and model are inspired by ANOVA. The method was developed by Laurent Excoffier, Peter Smouse and Joseph Quattro at Rutgers University in 1992. Since developing AMOVA, Excoffier has written a program for running such analyses. This program, which runs on Windows, is called Arlequin and is freely available on Excoffier's website. There are also implementations in R language in the ade4 and the pegas packages, both available on CRAN (Comprehensive R Archive Network). Another implementation is in Info-Gen, which also runs on Windows. The student version is free and fully functional. Native language of the application is Spanish but an English version is also available. An additional free statistical package, GenAlEx, is geared toward teaching as well as research and allows for complex genetic analyses to be employed and compared within the commonly used Microsoft Excel interface. This software allows for calculation of analyses such as AMOVA, as well as comparisons with other types of closely related statistics including F-statistics and Shannon's index, and more.
Sources: en.wikipedia.org
Method validation is the documented process of confirming that an HPLC procedure is suitable for its intended use. It evaluates accuracy, precision, specificity, linearity, range, detection limits, and robustness. Validation criteria depend on the regulatory context and the sample type.
System suitability tests are short checks performed before or during an HPLC run to verify instrument and method performance. They often include resolution, tailing factor, theoretical plates, and injection precision. Results must meet predefined limits for sample data to be accepted.
HPLC retention time alone cannot definitively identify an unknown substance. A match with a reference standard under identical conditions provides supporting evidence. Confirmation typically requires mass spectrometry, nuclear magnetic resonance, or another orthogonal technique.
HPLC separates and detects individual compounds in a liquid sample, producing peaks at characteristic retention times. Peak area or height can be used to estimate concentration when calibrated with known standards. It does not identify unknown compounds with certainty unless additional detectors or reference materials are used.