A practical reference on Mobile phase: what it is, how it behaves, what the literature reports, and where the honest uncertainties sit.
Reviewed 2026-08-01. Anything still debated is marked as such rather than presented as settled.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Common checks include retention time, peak area, resolution between critical pairs, tailing factor, and theoretical plate count. Results are compared with predefined limits, and a failed check requires investigation before sample results are reported. Quality control samples at low, middle, and high concentrations are injected at intervals to monitor accuracy and precision. Blank injections detect carryover and contamination, while control charts track performance over time.
Data handling and documentation are central to HPLC quality control. Electronic systems should have audit trails that record changes to methods, sequences, and results. Integration parameters, such as peak baseline and threshold, can affect reported areas and must be defined in advance. Out-of-specification results trigger a structured investigation that may include reanalysis, instrument checks, and review of sample preparation. Regulatory inspections often examine raw data, audit trails, and training records to verify that reported results are traceable and reliable.
Method validation establishes that an HPLC procedure is suitable for its intended use. Key parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Accuracy measures agreement with a true or accepted value, while precision describes repeatability and intermediate precision. Specificity confirms that the method measures the analyte without interference from impurities, degradants, or excipients. Validation is documented in a protocol and report, and acceptance criteria are set before experiments begin. Regulatory guidance varies by region, but the general principles are widely harmonized.
| Property | Value | Notes |
|---|---|---|
| Separation principle | Differential partitioning | Analytes distribute between mobile and stationary phases. |
| Mobile phase | Liquid solvent mixture | Composition controls retention and selectivity. |
| Stationary phase | Packed column particles | Often chemically bonded silica. |
| Typical detector | UV-Vis or photodiode array | Mass spectrometry is also common. |
| Common synonym | High-performance liquid chromatography | Abbreviated as HPLC. |
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
Detection commonly uses ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. Ultraviolet detection depends on molecular chromophores that absorb light at specific wavelengths. Mass spectrometry provides mass information and sensitive quantification, often after electrospray ionization. Before sample batches, performance checks examine resolution, elution time repeatability, peak symmetry, and plate count. Matrix effects and co-elution remain recognized uncertainties; formal validation studies and orthogonal detection help address them. Detector choice depends on analyte properties and required sensitivity.
High-performance liquid chromatography, or HPLC, separates dissolved compounds by passing a liquid mobile phase through a packed column. Components distribute differently between the stationary phase and the moving liquid, so they travel at different speeds and exit at different times. A detector records these eluting bands as peaks, and peak area or height relates to amount. The technique supports testing in pharmaceuticals, foods, environmental samples, and industrial chemicals. Quantification usually depends on calibration with known standards.
In quality control laboratories, HPLC testing supports batch release, raw material checks, stability studies, and impurity profiling. A validated method defines sample preparation, instrument settings, calibration, and acceptance criteria. Analysts compare results with specifications and investigate out-of-specification outcomes before a batch is approved. Documentation includes chromatograms, integration records, audit trails, and reagent details. Because results influence product decisions, laboratories follow formal quality systems and data integrity rules. The exact tests and limits depend on the material, its intended use, and the applicable regulatory framework.
Method validation examines whether an HPLC procedure is suitable for its intended purpose. Common parameters include accuracy, precision, specificity, linearity, range, detection limit, quantification limit, and robustness. Accuracy describes closeness to a true or accepted value, while precision describes agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from related substances. Robustness tests small deliberate changes in flow, temperature, or solvent composition. Validation is not a one-time event; methods may need partial revalidation after changes to instruments, columns, sample handling, or specification limits. Regulatory guidance provides frameworks, but some details remain method-specific.
The F1 fraction derives its name from the term "Fraction 1" and FO (written as a subscript letter "o", not "zero") derives its name from being the binding fraction for oligomycin, a type of naturally derived antibiotic that is able to inhibit the FO unit of ATP synthase. These functional regions consist of different protein subunits — refer to tables. This enzyme is used in synthesis of ATP through aerobic respiration. Located within the thylakoid membrane and the inner mitochondrial membrane, ATP synthase consists of two regions FO and F1. FO causes rotation of F1 and is made of c-ring and subunits a, two b, F6. F1 is made of α, β, γ, and δ subunits. F1 has a water-soluble part that can hydrolyze ATP. FO on the other hand has mainly hydrophobic regions. FO F1 creates a pathway for protons movement across the membrane.
After earning his doctorate in biochemistry, Lehninger held various faculty positions at the University of Wisconsin–Madison and the University of Chicago. In 1952, he went to the Johns Hopkins School of Medicine, assuming the title of DeLamar Professor of the Department of Biological Chemistry. He served in this position until 1978, when he was appointed to the role of University Professor of Medical Sciences. He held this title until his death in 1986. 1948 – Paul-Lewis Award in Enzyme Chemistry 1951 – Guggenheim Fellowship 1956 – Elected to the National Academy of Sciences 1959 – Elected to the American Academy of Arts and Sciences 1969 – Remsen Award of the American Chemical Society 1970 – American Philosophical Society 1986 – Passano Foundation Award Forthcoming in New Dictionary of Scientific Biography
A common SNP in the BDNF gene is rs6265. This point mutation in the coding sequence, a guanine to adenine switch at position 196, results in an amino acid switch: valine to methionine exchange at codon 66, Val66Met, which is in the prodomain of BDNF. Val66Met is unique to humans. The mutation interferes with normal translation and intracellular trafficking of BDNF mRNA, as it destabilizes the mRNA and renders it prone to degradation. The proteins resulting from mRNA that does get translated, are not trafficked and secreted normally, as the amino acid change occurs on the portion of the prodomain where sortilin binds; and sortilin is essential for normal trafficking. The Val66Met mutation results in a reduction of hippocampal tissue and has since been reported in a high number of individuals with learning and memory disorders, anxiety disorders, major depression, and neurodegenerative diseases such as Alzheimer's and Parkinson's. A meta-analysis indicates that the BDNF Val66Met variant is not associated with serum BDNF.
Adenylyl cyclase is regulated by G proteins, which can be found in the monomeric form or the heterotrimeric form, consisting of three subunits. Adenylyl cyclase activity is controlled by heterotrimeric G proteins. The inactive or inhibitory form exists when the complex consists of alpha, beta, and gamma subunits, with GDP bound to the alpha subunit. In order to become active, a ligand must bind to the receptor and cause a conformational change. This conformational change causes the alpha subunit to dissociate from the complex and become bound to GTP. This G-alpha-GTP complex then binds to adenylyl cyclase and causes activation and the release of cAMP. Since a good signal requires the help of enzymes, which turn on and off signals quickly, there must also be a mechanism in which adenylyl cyclase deactivates and inhibits cAMP. The deactivation of the active G-alpha-GTP complex is accomplished rapidly by GTP hydrolysis due to the reaction being catalyzed by the intrinsic enzymatic activity of GTPase located in the alpha subunit. It is also regulated by forskolin, as well as other isoform-specific effectors:
Sources: en.wikipedia.org
Korvezee was the youngest of two daughters of the pastor Willem Korvezee (1858–1913) and his wife Baukje Andringa (1874–1952). Her older sister, Elisabeth “Bets” Korvezee, later became the first female national archivist in the Netherlands. After their father's death in 1913, the family lived in The Hague, where both sisters attended the third municipal HBS, known as the “HBS-voor-jongens” (boys’ HBS), and Antonia showed particular talent for mathematics. She went on to study chemical technology at the Delft Institute of Technology, graduating cum laude in 1922. She then worked as an assistant, first in the department of analytical chemistry and from 1924 to 1938 in the laboratory of Scheffer. Under Frans Everhardus Cornelis Scheffer, she completed her doctorate cum laude in 1930 with a thesis titled “Copper chlorides as a catalyst for the Deacon process.” Between 1930 and 1932, she spent two six-month periods in Paris conducting research on radioactivity in Marie Curie’s laboratory. In 1935, her temporary appointment at Delft was made permanent, and she was appointed lecturer in radioactive decay. Korvezee was passed over for a professorship three times, first nominated in 1936 for the chair of analytical chemistry, and again in 1940 for the chair of physical chemistry despite ranking third in the nomination process.
Homopolymers of amino acids (such as polylysine) can adopt α-helical structure at low temperature that is "melted out" at high temperatures. This helix–coil transition was once thought to be analogous to protein denaturation. The statistical mechanics of this transition can be modeled using an elegant transfer matrix method, characterized by two parameters: the propensity to initiate a helix and the propensity to extend a helix.
After dendritic cells have phagocytosed pathogens, they usually migrate to the vast network of lymph vessels and are carried by lymph flow to the draining lymph nodes. Each lymph node is a collection point where APCs can interact with T cells. During the migration, DCs undergo a process of maturation: they lose most of their ability to further engulf pathogens and they mature by changing surface expression of MHC and co-stimulatory molecules, as well as increased production of cytokines. The internalized antigen is digested into smaller peptides containing epitopes, which are then presented to T cells by the MHC. B cells reside in the lymph node. Once their B cell receptor binds to an antigen, they can interact with activated helper T cells, as described above. A dendritic cell that interacts with an already-activated helper T cell can become licensed. This occurs through the interaction of co-stimulatory molecules including B7 and CD40 on the dendritic cell, with CD28 and CD40 ligand on the T cell. Only licensed dendritic cells are able to activate cytotoxic T cells. T cell licensing of dendritic cells is key for activation of cytotoxic T cells for many pathogens, although the extent to which T cell help is needed may vary. In MHC class I and class II molecules, only certain epitopes of an internalized peptide can be presented. These epitopes are termed immunodominant.
Benninghoven graduated from the University of Cologne in 1961 where he worked with Fritz Kirchner (1896–1967) and completed his habilitation in surface physics in Cologne two years later. He first worked as professor in Cologne from 1965 to 1973 until he moved to a full professor position in experimental physics at the University of Münster in 1972. He worked on static secondary ion mass spectrometry (SIMS) and its applications, and developed SIMS instruments. In 1989 he co-founded IonTOF, a company that became a world-leader in TOF-SIMS instrumentation. He has written over 300 scientific articles and several books on the topic of SIMS, many of which have become reference works on SIMS. For his work, he has received the Technology Transfer prize (German Ministry of Education and Research) and the 1984 Gaede-Langmuir Prize (American Vacuum Society) for the development of concepts and instrumentation in static secondary ion mass spectrometry and the demonstration of its usefulness in manifold applications. In 1990 he shared the Fritz-Pregl-Medaille of the Austrian Society of Analytical Chemistry with Wilhelm Simon. From 1977 to 1983, he was president of the German Vacuum Society (part of the German Physical Society).
Antimicrobial peptides (AMPs), also called host defence peptides (HDPs) are part of the innate immune response found among all classes of life. Fundamental differences exist between prokaryotic and eukaryotic cells that may represent targets for antimicrobial peptides. These peptides are potent, broad spectrum antimicrobials which demonstrate potential as novel therapeutic agents. Antimicrobial peptides have been demonstrated to kill Gram negative and Gram positive bacteria, enveloped viruses, fungi and even transformed or cancerous cells. Unlike the majority of conventional antibiotics it appears that antimicrobial peptides frequently destabilize biological membranes, can form transmembrane channels, and may also have the ability to enhance immunity by functioning as immunomodulators.
Sources: en.wikipedia.org
Overall, automated synthesis has improved the efficiency for the parallel synthesis and combinatorial methods of polymers. These techniques aim to design new materials, in addition to studying the relationships of their structure and properties. However, while screening for polymers enables this investigation, it becomes increasingly demanding for researchers to create the libraries for these synthetic compositions. In addition, preparation requires a large number of repetitive reactions to be completed, leading to an immense burden of planning and labor. Using automated synthesis, this process can be refined, increasing the efficiency of the reaction and removing the impact of human error.
Automated iterative homologation enables stepwise construction of carbon chains through repeated one-carbon extensions of boronic esters. Two reactions adapted to automation are the Matteson homologation, which inserts a methylene unit via chloromethyllithium, and chiral carbenoid homologation, which uses lithiated benzoate esters. Both methods have been implemented on robotic platforms under low-temperature, inert conditions. Using these techniques, up to six consecutive C(sp³)–C(sp³) bond-forming homologations have been performed without manual intervention, representing the highest number reported in an automated synthesis. The approach has also been applied to the synthesis of intermediates of the natural product (+)-kalkitoxin.
Over the years, multiple synthesizers have been developed to assist with automated synthesis, including the Chemspeed Accelerator (SLT106, SLT II, ASW2000, SwingSLT, Autoplant A100, and SLT100), the Symyx system, and Freeslate ScPPR. Recently, researchers have investigated the optimization of these methods for controlled/living radical polymerization (CLRP), which faces issues with oxygen intolerance. This research has led to the development of oxygen-tolerant CLRP, including with the use of enzyme degassing of RAFT (Enz-RAFT), atom-transfer radical (ATRP) that possesses tolerance to air, and photoinduced electron/energy transfer–RAFT (PET–RAFT) polymerization. Through the use of liquid-handling robots, Tamasi et al. demonstrated the use of automated synthesis with executing multi-step procedures, enabling the reactions to investigate more elaborate schemes, such as with scale and complexity. Lee Cronin and his team have developed a modular synthesis machine called the chemputer which uses a dedicated programming language for chemical synthesis.
Ethane-1,2-dithiol, also known as EDT, is a colorless liquid with the formula C2H4(SH)2. It has a very characteristic odor which is compared by many people to rotten cabbage. It is a common building block in organic synthesis and an excellent ligand for metal ions. Ethane-1,2-dithiol is made commercially by the reaction of 1,2-dichloroethane with aqueous sodium bisulfide. In the laboratory, it can also be prepared by the action of 1,2-dibromoethane on thiourea followed by hydrolysis. 1,2-Ethanedithiol is a weak acid, typical of alkyl thiols. In the presence of base and an alkylating agent, 1,2-ethanedithiol converts to thioethers: HS(CH2)2SH + 2 NR3 + 2 R'I → R'S(CH2)2SR' + 2 [R3NH]I Oxidation of 1,2-ethanedithiol gives a series of oligomers, including the cyclic bis(disulfide). As a 1,2-dithiol, this compound reacts with aldehydes and ketones to give 1,3-dithiolanes, which can be useful intermediates.
Nanoghosts are nanosized vesicles containing a chosen drug delivery payload manufactured from extracted leukocyte membranes with the cell cytoplasm content removed. The use of biological membranes serves to mask the particles from the immune system to reduce the likelihood of an immunogenic response, as well as to extend circulation of the particles in the blood. They are produced by homogenizing the cells to remove the cytosol, and then sonicating the empty cell membranes to create nanoghosts between 100 and 200 nm in diameter. Membranes used to make nanoghosts harvested form red blood cells have been shown to circulate for about 120 days and avoid phagocytotic cells. Neutrophil based nanoghosts retain the chemotaxis capacity of neutrophils to sites of inflammation, which encourages tumor targeting. NK based nanoghosts exhibit metastatic cancer targeting behavior. Monocyte based nanoghosts are effective at infiltrating the tumor microenvironment. Mesenchymal stem cell derived nanoghosts exhibit cancer targeting properties.
Sources: en.wikipedia.org
HPLC separates and detects individual compounds in a liquid sample, producing peaks at characteristic retention times. Peak area or height can be used to estimate concentration when calibrated with known standards. It does not identify unknown compounds with certainty unless additional detectors or reference materials are used.
Pressure drives the liquid mobile phase through a column packed with small particles. Without pressure, flow would be very slow or stop because the packed bed resists liquid movement. Modern pumps maintain a steady flow despite the resistance.
A chromatogram is a plot of detector signal against time after sample injection. Each peak represents a compound or group of compounds eluting from the column. Retention time and peak area are the main measurements read from the plot.
System suitability is a set of checks that confirm the instrument and method perform within limits before sample analysis. It typically includes resolution, tailing factor, retention time, and peak area reproducibility. If a check fails, the run is invalidated until the cause is resolved.