This is a working overview of stationary phase, written for readers who want more than a one-paragraph summary but less than a textbook.
This page was last updated on 2026-05-26 and is reviewed periodically as new material appears.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Closeness to a reference value. |
| Validation parameter | Precision | Repeatability or intermediate precision. |
| Validation parameter | Linearity | Proportional response across a range. |
| System suitability check | Resolution | Separation between adjacent peaks. |
| Quality control tool | Control chart | Tracks results over time for trends. |
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
High-performance liquid chromatography is an analytical technique that separates components of a liquid sample by passing it through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in interaction with the stationary phase cause analytes to migrate at different rates. Detectors record elution as peaks, and a data system converts signals into a chromatogram. The method is suited to compounds that dissolve in a liquid and are not volatile enough for gas chromatography.
Reversed-phase chromatography dominates modern HPLC testing, using a nonpolar stationary phase such as chemically bonded octadecyl groups and a polar mobile phase of water mixed with organic solvent. Analytes partition between the mobile and stationary phases according to hydrophobicity. Gradient elution changes the mobile phase composition over time to separate compounds with a wide range of retention. Isocratic elution keeps the composition constant and is simpler for routine assays. Column temperature, pH, and flow rate influence selectivity, peak shape, and retention time, so these parameters are controlled during a validated method.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
The American Society for Mass Spectrometry (ASMS) is a professional association based in the United States that supports the scientific field of mass spectrometry. As of 2018, the society had approximately 10,000 members primarily from the US, but also from around the world. The society holds a large annual meeting, typically in late May or early June as well as other topical conferences and workshops. The society publishes the Journal of the American Society for Mass Spectrometry.
With ring-opening polymerization, automated synthesis has been used for rapid screening and optimization, including with catalyst + initiator systems and their polymerization conditions. For example, Hoogenboom et al. determined the optimal temperature for the polymerization of 2-ethyl-2-oxazoline in dimethylacetamide (DMAc), allowing for individual heating of the parallel reactors, which shortened the time needed for preparation and analysis. To aid with the catalyst research for polyolefins, Symyx Technologies Inc. used automated synthesis to create a library of palladium and nickel catalysts, which were screened for ethylene polymerization. This process found that the largest polyethylene polymers were created by the complexes with the highest steric hindrance for the ortho-positions of the aryl rings, while electronic factors did not influence yield or molecular weight. In addition, Tuchbreiter and Mülhaupt used automated synthesis to demonstrate the improvements of minireactors for the polymerization of olefins, with quality improving as compared to utilizing simple arrays.
A 15-hydroxyicosatetraenoate dehydrogenase metabolizes 15-hydroxyicosatetraenoic acid (i.e. 15(S)-hydroxy-5Z,8Z,11Z,13E-eicosatetraenoic acid or 15-HETE) to its 15-keto analog, 15-oxo-ETE, using NAD+ and NADH rather than NADP+ and NADPH as its co-factors. 15-Oxo-ETE appears to have a somewhat different spectrum of activities than its precursor, 15-HETE (see 15-Hydroxyicosatetraenoic acid
National teams April 29 – May 1: 2018 FIBA 3x3 Asia Cup in Shenzhen Men: Australia defeated Mongolia, 17–16, in the final. Japan took third place. Women: New Zealand defeated China, 14–11, in the final. Australia took third place. August 5 – 11: 2018 FIBA Under-18 Asian Championship in Thailand In the final, Australia defeated New Zealand, 73–62, to win their 1st title. China took third place. Note: All teams mentioned here, plus Philippines, have qualified to compete at the 2019 FIBA Under-19 Basketball World Cup. October 28 – November 3: 2018 FIBA Under-18 Women's Asian Championship in Bangalore China defeated Japan, 89–76, to win their fifth consecutive and 16th overall FIBA Under-18 Women's Asian Championship title. Australia took third place. Note: All teams mentioned here, plus South Korea, have qualified to compete at the 2019 FIBA Under-19 Women's Basketball World Cup. Clubs teams November 17, 2017 – May 2: 2017–18 ABL season San Miguel Alab Pilipinas defeated Mono Vampire, 3–2 in games played in a 5-legged final, to win their first ABL title. July 17 – 22: Summer Super 8 in Macau Guangzhou Long-Lions defeated Seoul Samsung Thunders, 78–72, to win their first title. Incheon Electroland Elephants took third place.
Individuals with 3-M syndrome have severe prenatal growth retardation due to growth delays during fetal development resulting in a low birth weight. Growth delays continue after birth throughout childhood and adolescence, ultimately leading to a short stature. Growth delays and immature bone development (growth retardation and delayed bone maturation) typically continue after birth (postnatally), leading to short stature (dwarfism) with proportional development of the arms and legs (as opposed to short stature with abnormally small arms and legs). In most cases, infants with 3M syndrome are unusually small and have a low birth weight despite being carried to term.
Sources: en.wikipedia.org
Adenomatous polyposis coli protein 2 is a protein that in humans is encoded by the APC2 gene. This is a dual-functional protein which is especially prevalant in the developing brain, and involved in cell signaling (specifically Wnt signaling) and stabilizing the cytoskeleton. Frizzled receptors are a type of cell receptor involved in a variety of functions including embryonic development and cell proliferation. These receptors trigger a cascade of reactions called the Wnt signaling pathway that eventually leads to interaction with the DNA via the protein beta-catenin, which affects which proteins get produced by the cell. The APC2 protein promotes the formation of a protein complex which is involved in breaking down the protein beta-catenin. The APC2 protein stabilizes microtubules, which are part of the cell cytoskeleton. It may also be involved in the regulation of actin fibers my means of GTPase activation (specifically the Rho family).
APHL works with public health partners to build the foundation for quality testing, comprehensive standards and integrated public health laboratory systems. One of the initiatives, the Laboratory System Improvement Program, provides individual assessments of public health laboratory systems that include engaging stakeholders for system improvement, performance, implementation of strategies and continual evaluation. APHL also collaborates on the National Laboratory System project to build a public-private network of laboratories nationwide. APHL monitors trends in public health laboratory diagnostics, personnel and infrastructure in order to create quality assurance standards. By using these data points to benchmark individual labs against national norms, APHL is able to home in on key issues and help raise the standard of laboratory systems. Member labs have access to research and survey data online, which enables them to leverage new information quickly to identify promising strategies and practices.
It is thought that high glucagon levels and lack of insulin production are the main triggers for the metabolic issues associated with Type I diabetes, in particular maintaining normal blood glucose levels, formation of ketone bodies, and formation of urea. One finding of note is that the glucagon response to hypoglycemia is completely absent in patients with Type I diabetes. Consistently high glucagon concentrations in the blood can lead to diabetic ketoacidosis, which is when ketones from lipid breakdown build up in the blood, which can lead to dangerously low blood glucose levels, low potassium levels, and in extreme cases cerebral edema. It has been proposed that the reason for the high levels of glucagon found in the plasma of patients with Type I diabetes is the absence of beta cells producing insulin and the reciprocal effect this has on delta cells and the secretion of somatostatin.
Adenomatous polyposis coli protein 2 is a protein that in humans is encoded by the APC2 gene. This is a dual-functional protein which is especially prevalant in the developing brain, and involved in cell signaling (specifically Wnt signaling) and stabilizing the cytoskeleton. Frizzled receptors are a type of cell receptor involved in a variety of functions including embryonic development and cell proliferation. These receptors trigger a cascade of reactions called the Wnt signaling pathway that eventually leads to interaction with the DNA via the protein beta-catenin, which affects which proteins get produced by the cell. The APC2 protein promotes the formation of a protein complex which is involved in breaking down the protein beta-catenin. The APC2 protein stabilizes microtubules, which are part of the cell cytoskeleton. It may also be involved in the regulation of actin fibers my means of GTPase activation (specifically the Rho family).
In 1884, Svante Arrhenius attributed the properties of acidity to hydrogen cations (H+), later described as protons or hydrons. An Arrhenius acid is a substance that, when added to water, increases the concentration of H+ ions in the water. Chemists often write H+(aq) and refer to the hydrogen cation when describing acid–base reactions but the free hydrogen nucleus, a proton, does not exist alone in water, it exists as the hydronium ion (H3O+) or other forms (H5O2+, H9O4+). Thus, an Arrhenius acid can also be described as a substance that increases the concentration of hydronium ions when added to water. Examples include molecular substances such as hydrogen chloride and acetic acid. An Arrhenius base, on the other hand, is a substance that increases the concentration of hydroxide (OH−) ions when dissolved in water. This decreases the concentration of hydronium because the ions react to form H2O molecules:
Sources: en.wikipedia.org
Method validation is the documented process of showing that an HPLC procedure produces reliable results for a defined purpose. It examines parameters such as accuracy, precision, specificity, linearity, and robustness. Regulators and quality systems often require validation before routine use.
System suitability is a set of checks run on the chromatographic system before sample analysis. It confirms that resolution, peak shape, retention time, and response meet predefined limits. Failure can invalidate the run and trigger corrective action.
Blank injections reveal peaks or baseline disturbances that come from solvents, reagents, or the instrument rather than the sample. They help distinguish contamination from actual analyte signals. Comparing blanks with sample runs supports accurate interpretation.
System suitability is typically performed before each batch or according to the validated method and laboratory procedure. Some long runs include periodic checks during analysis. The required frequency depends on regulatory expectations and method performance.